Here’s what you need :

• 2 carton boards 100cm*70cm
• a good pair of scissors
• one marker pen to mark the measures
• Ruler (40cm or more)
• A measuring tape
• Tin foil (to act as the reflector in the softbox)
• Strong scotch tape
• An utility knife

Dig’n and start the project

Lets start:

The first thing we’ll have to do is getting 4 squares 40cm*40cm size.

So that’s how I did it:

1. Put a mark on the bottom wide side of the carton board every 40cm.Repeat that on the top wide side too.

2.Do the same for the short side of the carton board (this will help you get the right 40cm*40cm squares).

3.after you have those marks,draw the line that make the 40cm*40cm squares.

4. Use your utility knife to cut 4 identical 40cm*40cm squares.This what you’ll get then:

5. On each square make a mark every 10cm as in the picture bellow (right and left sides):

6. At the bottom of the square make 2 marks 15cm from the left side and 15cm from the right side (that 10cm space will be where your flash gun will get into the soft box):

7. I missed one picture here,so I’ll make a draw of how each side of the soft box has to be cut.

8.Cut those squares and you’ll get this  result:

9.Now lets start putting them together.I taped two squares together and then taped them together to form the soft box frame:

OK That the end of part I on DIY Soft Box 40cm*40cm for Less Than 10 bucks,

Part II

If you’ve got up to here are a step away from this:

After building the simple to do DIY softbox box,it is time to make the “speed ring” for the soft box and put the diffuser on.

What you need here is simple:

• 40cm*40cm DIY soft box (you did it in part I)
• A 10 cm diameter pipe :can be a plastic pipe,plastic jar of anything stiff enough to hold the soft box and about 20-25cm long.
• A good Sellotape (masking tape).

and lets go

1. Get the “speed ring” ready to use:as a speed ring I used a small baby food can (I have a lot of them cause I a have a baby boy!!!).Open the bottom side of the can with a can opener.Drill a small hole it the middle of the can (thats where the tripod will attach to the can,so don’t make the hole too big).

2.Use the masking tape to attach your new speed ring to the soft box.Tape it good so it won’t come apart.

3.For the soft box diffuser you can use almost every material,I used here drawing paper.Get a rectangle 50cm*50cm and cut at corners 5cm*5cm squares.Put it on the floor/table and at the center of it place the soft box.Glue each side of the soft box to the drawing paper.

Great by now you already own your first DIY soft box!!!

If you followed the instructions you should have this softbox ready to use:

Stay tuned for my first use of my first cheap DIY softbox:

Just some moments after I finished building it’I took some flowers shot,This is the setup:

Share any tips or thoughts about this project!

Related posts:

1. DIY Small softbox from Shoe box Well we had a sale in the Adidas outlet store...
2. One light simple product photography setup Hey this time I bring you a very simple product...
3. Great blog by David James Williams Well I found David’s site as I was looking...

Related posts brought to you by Yet Another Related Posts Plugin.

After building the simple to do DIY soft box,it is time to make the “speed ring” for the soft box and put the diffuser on.

What you need here is simple:

• 40cm*40cm DIY soft box (you did it in part I)
• A 10 cm diameter pipe :can be a plastic pipe,plastic jar of anything stiff enough to hold the soft box and about 20-25cm long.
• A good Sellotape (masking tape).

and lets go

1. Get the “speed ring” ready to use:as a speed ring I used a small baby food can (I have a lot of them cause I a have a baby boy!!!).Open the bottom side of the can with a can opener.Drill a small hole it the middle of the can (thats where the tripod will attach to the can,so don’t make the hole too big).

2.Use the masking tape to attach your new speed ring to the soft box.Tape it good so it won’t come apart.

3.For the soft box diffuser you can use almost every material,I used here drawing paper.Get a rectangle 50cm*50cm and cut at corners 5cm*5cm squares.Put it on the floor/table and at the center of it place the soft box.Glue each side of the soft box to the drawing paper.

Great by now you already own your first DIY soft box!!!

If you followed the instructions you should have this softbox ready to use:

Share tuned for my first use of my first cheap DIY softbox:

Just some moments after I finished building it’I took some flowers shot,This is the setup:

Share any tips or thoughts about this project!

Related posts:

1. Great blog by David James Williams Well I found David’s site as I was looking...
2. DIY Small softbox from Shoe box Well we had a sale in the Adidas outlet store...

Related posts brought to you by Yet Another Related Posts Plugin.

So lets start working.

Here’s what you need :

• 2 carton boards 100cm*70cm
• a good pair of scisors
• one marker pen to mark the misures
• Ruler (40cm or more)
• A measuring tape
• Tin foil (to act as the reflector in the softbox)
• Strong scotch tape
• An utility knife

Lets start:

The first thing we’ll have to do is getting 4 squares 40cm*40cm size.

So that’s how I did it:

1. Put a mark on the bottom wide side of the carton board every 40cm.Repeat that on the top wide side too.

2.Do the same for the short side of the carton board (this will help you get the right 40cm*40cm squares).

3.after you have those marks,draw the line that make the 40cm*40cm squares.

4. Use your utility knife to cut 4 identical 40cm*40cm squares.This what you’ll get then:

5. On each square make a mark every 10cm as in the picture bellow (right and left sides):

6. At the bottom of the square make 2 marks 15cm from the left side and 15cm from the right side (that 10cm space will be where your flash gun will get into the soft box):

7. I missed one picture here,so I’ll make a draw of how each side of the soft box has to be cut.

8.Cut those squares and you’ll get this  result:

9.Now lets start putting them together.I taped two squares together and then taped them together to form the soft box frame:

OK That the end of part I on DIY Soft Box 40cm*40cm for Less Than 10 bucks,

In the next part close the DIY Soft Box 40cm*40cm for Less Than 10 bucks, and put a bracket on it.

Share your thoughts with us and comment here.

Enjoy

Related posts:

1. One light simple product photography setup Hey this time I bring you a very simple product...
2. DIY Small softbox from Shoe box Well we had a sale in the Adidas outlet store...
3. DIY Photography reflector 3 in 1White/Silver/Gold This is going to be a really quick and amazingly...

Related posts brought to you by Yet Another Related Posts Plugin.